Beko Washing Machine Error Codes: Complete Troubleshooting & Reset Guide

---

Introduction

Is your Beko washing machine displaying strange error codes like E01, E10, or E20? Error messages can be frustrating, but most issues can be fixed at home with simple troubleshooting.

This Beko washing machine error codes guide covers:
✔ All common Beko error codes (with explanations)
✔ Step-by-step reset methods (soft/hard reset, factory reset)
✔ Diagnostic mode activation (to pinpoint problems)
✔ Free downloadable PDF (Beko error code list for reference)

Let’s decode your washer’s warnings and get it running again!

Understanding Beko’s Error Code System

Beko washing machines use a sophisticated diagnostic system that displays specific error codes when operational problems occur. These alphanumeric combinations provide crucial information about what’s malfunctioning in your appliance. The codes follow a logical pattern where:

• E01-E20 series typically indicate water supply or drainage issues

• E30-E50 series often relate to mechanical/spin problems

• E60-E90 series usually signify electronic/sensor failures

Each code corresponds to specific components or systems within your washing machine, helping you pinpoint exactly where the problem lies without unnecessary guesswork.

Common Beko Washing Machine Error Codes

1. Drainage & Water Supply Errors

E01: Water Inlet Failure

What it means: Your Beko washing machine isn’t receiving adequate water supply.

Detailed troubleshooting:

1. Check water supply valves behind the machine – ensure both hot and cold are fully open

2. Inspect inlet hoses for kinks or blockages

3. Clean inlet filters (located where hoses connect to the machine)

4. Test water pressure – minimum 0.5 bar required for proper operation

Pro tip: During winter, check that pipes haven’t frozen if installed in a cold area.

E10: Drainage Problem

What it means: The machine cannot properly drain water after washing.

Step-by-step solution:

1. Locate and clean the drain pump filter (usually behind a small door at the front bottom)

2. Check drain hose for obstructions or improper installation

3. Inspect pump operation by running a drain-only cycle

4. Verify proper hose height (should be 60-100cm from floor)

Common causes: Coins, buttons, or lint clogging the system.

E20: Water Leakage Detected

What it means: The machine’s sensors detected unexpected water presence.

Troubleshooting procedure:

1. Inspect door seal/gasket for tears or debris

2. Check all hose connections for tightness

3. Examine detergent drawer for overflows

4. Verify tub condition for cracks (rare but possible)

Safety note: Always unplug the machine before inspecting for leaks.

2. Spin & Motor Errors

E30: Spin Imbalance

What it means: The laundry load is unevenly distributed during spin cycle.

Comprehensive solution:

1. Pause the cycle and redistribute clothes evenly

2. Check for oversized items (blankets, comforters) that may unbalance

3. Verify machine leveling – use a spirit level to check

4. Inspect suspension springs if problem persists

Prevention: Mix large and small items when loading.

E40: Motor Communication Error

What it means: The control board isn’t receiving proper signals from the motor.

Troubleshooting steps:

1. Perform hard reset (unplug for 10 minutes)

2. Check motor connections (requires partial disassembly)

3. Inspect carbon brushes if applicable to your model

4. Test motor windings with multimeter (advanced users)

Technical note: This often requires professional diagnosis if reset doesn’t help.

3. Sensor & Electrical Faults

E60: Temperature Sensor Failure

What it means: The system can’t properly monitor water temperature.

Diagnosis and repair:

1. Check sensor connections at control board

2. Test sensor resistance (should be 10-50kΩ at room temp)

3. Inspect wiring for damage

4. Consider replacement if faulty

Important: Always disconnect power before accessing electrical components.

E90: Control Board Error

What it means: The main electronic control unit has malfunctioned.

What to do:

1. Attempt full reset (unplug overnight)

2. Check for power surges that may have damaged board

3. Inspect for visible damage (burn marks, swollen capacitors)

4. Professional repair recommended for this complex component

Cost consideration: Control board replacement often costs 40-60% of a new machine.

For solutions to common washing machine problems—like leaks, spin failures, or unexplained error codes—check out our comprehensive guide on Common Washing Machine Problems & Fixes. This resource complements our Beko Washing Machine Error Codes troubleshooting by covering universal issues across brands, including drainage blockages, unbalanced loads, and power failures.

---

How to Reset a Beko Washing Machine

Method 1: Soft Reset (For Minor Glitches)

1. Press and hold “Start/Pause” for 5 seconds.

2. Wait for the machine to beep and restart.

Method 2: Hard Reset (For Persistent Errors)

1. Unplug the washer for 10 minutes.

2. Restore power and restart the cycle.

Method 3: Factory Reset (For Major Issues)

1. Turn the dial to “Rinse”.

2. Press “Temperature” + “Spin Speed” simultaneously for 3 seconds.

3. The display will flash—release buttons to complete reset.

---

How to Enter Diagnostic Mode

1. Turn off the machine.

2. Press “Spin Speed” + “Pre-Wash” + “Start/Pause” together.

3. The display will show test codes (refer to manual).

---

FAQs: Beko Washing Machine Error Codes

1. What are the most common Beko Washing Machine Error Codes?

The most frequent Beko Washing Machine Error Codes include E01 (water inlet failure), E10 (drainage issue), E30 (spin imbalance), and E90 (control board fault). Each code indicates specific component failures requiring targeted troubleshooting.

---

2. How do I reset Beko Washing Machine Error Codes?

For most Beko Washing Machine Error Codes, try:

1. Soft reset: Hold “Start/Pause” for 5 seconds.

2. Hard reset: Unplug for 10 minutes.

3. Factory reset: Dial to “Rinse” + press “Temp” + “Spin Speed” for 3 seconds.

---

3. Why does my Beko washer show E10 (drainage error)?

E10 in Beko Washing Machine Error Codes signals a clogged drain system. Clean the pump filter (bottom front panel) and check the drain hose for obstructions like coins or lint.

---

4. What does Beko error code E30 mean?

E30 among Beko Washing Machine Error Codes indicates unbalanced laundry. Redistribute clothes evenly and ensure the machine is level. Persistent errors may point to broken suspension springs.

---

5. How do I fix Beko Washing Machine Error Code E01?

E01 means low water supply. Verify:
✔ Water valves are fully open
✔ Inlet hoses aren’t kinked
✔ Filters (where hoses connect) are clean

---

6. Is Beko error code E90 repairable at home?

No. E90 in Beko Washing Machine Error Codes signals control board failure. This complex electronic issue requires professional repair or board replacement to avoid further damage.

---

7. Where can I find a complete list of Beko Washing Machine Error Codes?

Download our free Beko Washing Machine Error Codes PDF (linked above) covering all models, including rare codes like E60 (sensor failure) and E40 (motor issues).

---

8. Why does my Beko washer keep displaying different error codes?

Multiple Beko Washing Machine Error Codes suggest:

• Power surges damaging electronics

• Main control board failure

• Loose wiring connections
  Unplug the machine overnight and consult a technician if persistent.

---

9. How do I enter diagnostic mode for Beko Washing Machine Error Codes?

To access hidden Beko Washing Machine Error Codes:

1. Power off the machine.

2. Press “Spin Speed” + “Pre-Wash” + “Start/Pause” simultaneously.

3. Note flashing lights correlating to component tests.

---

10. Can Beko Washing Machine Error Codes be prevented?

Yes! Reduce Beko Washing Machine Error Codes by:
✔ Cleaning the drain filter monthly
✔ Using HE detergent only
✔ Avoiding overloading
✔ Scheduling annual professional maintenance

When to Call a Professional for Beko Washing Machine Error Codes

While many Beko Washing Machine Error Codes can be resolved with simple troubleshooting, some issues require professional expertise. If you encounter any of the following scenarios, it’s time to call a certified Beko washing machine repair technician.

---

1. ⚠️ Beko Washing Machine Error Codes Persist After Resetting

If Beko Washing Machine Error Codes (such as E90, E40, or E60) continue appearing after multiple reset attempts, the problem may involve:

• Faulty control board (requires replacement)

• Damaged wiring or sensors (needs professional diagnosis)

• Internal software glitches (may require firmware updates)

🔹 Why DIY Won’t Work:

• Advanced diagnostics tools are needed.

• Incorrect repairs can worsen damage.

• Electrical components risk further failure if mishandled.

---

2. ⚠️ Internal Water Leaks (Especially with Codes E20 or E10)

If your Beko washing machine leaks internally (even without visible Beko Washing Machine Error Codes), possible causes include:

• Cracked tub or seal

• Faulty water inlet valve

• Damaged drain pump housing

🔹 Why Professional Help is Crucial:

• Leaks can cause mold, electrical hazards, or floor damage.

• Seals and tubs require specialized tools for replacement.

• Improper sealing leads to recurring leaks.

---

3. ⚠️ Grinding, Knocking, or Loud Motor Noises (Often with E30 or E40 Codes)

Unusual noises (especially during spin cycles) suggest:

• Worn-out bearings (loud rumbling)

• Broken drive belt (squealing/slapping sounds)

• Failing motor (intermittent humming or clicking)

🔹 Why You Need a Pro:

• Motor/bearing replacements are complex.

• Misalignment can destroy other components.

• DIY disassembly often voids warranties.

---

4. ⚠️ Burning Smell or Electrical Issues

If you notice:

• Burning odors (overheating motor/wiring)

• Sparks or smoke (short circuits)

• Tripped circuit breakers (power supply faults)

🚨 Immediate Action Required:

1. Unplug the washer immediately.

2. Do NOT attempt to restart.

3. Call a professional for emergency repairs.

---

5. ⚠️ Washer Won’t Power On (No Display or Error Codes)

If the machine is completely unresponsive:

• Blown fuse or tripped breaker (simple fix)

• Faulty power cord (replacement needed)

• Dead control board (professional repair)

🔹 Why DIY is Risky:

• Electrical testing requires a multimeter.

• Incorrect wiring can be dangerous.

Final Checklist: When to Call for Help vs. DIY

---

Prevent Future Errors

✔ Clean the drain filter monthly
✔ Use HE detergent only
✔ Avoid overloading

For professional Beko Washing Machine Error Codes  in Nepal, trust the experts at SmartCare. With same-day service, genuine spare parts, and affordable pricing, SmartCare offers reliable solutions for all Beko models. Whether you need a routine checkup or urgent repairs, visit their website to schedule an appointment and keep your washing machine in top condition!